painting camouflage on model planes

02 Jan painting camouflage on model planes

I say sort of because, while they are straight lines when viewed straight on, the gentle curve of the tailplanes means you can't just slap a piece of tape on there and have it match up. Knowing where the demarcation falls and where I will be masking, I want to make sure that the color goes well beyond that to ensure solid color. First, that is the flattest point on the tail, and second, I needed to press the tape into the rudder trough. What may work with your last paint may not be the best setup with a new paint. I like to start by masking some of the flatter surfaces. Notify me of follow-up comments by email. Cut the mask a bit beyond where it will need to stop in this instance, so the excess can wrap under the wing. FREE Delivery on orders over £10 for books or over £20 for other categories shipped by Amazon. If I used the cups for enamels, I would discard the cups. By using simple paper masks here, I both protected the paint and gave myself a little boost in time, as I did not have to wait for the white to dry fully (although, given the thinness of the coat, it probably had at that point; that's a major benefit to lacquers, their drying time is very short). Camouflaged scale models can be challenging to paint. The small distance between mask and model will create the softer lines. I think what I like most about them is the precision they allow. 3. This kind of paint scheme is very hard to achieve with brush painting, and you should really use an airbrush . Testing AK Interactive's Weathering Pencils, Basic Modeling Skills: Applying Waterslide Decals. See the section on Surface Prep. List of WWII and Modern Aircraft Camouflage colors based on official documentation Oficial Name Model Air Name Ref. No matter how often people have insisted that “Tamiya tape never sticks”, I’ve had it lift off paint (water based acrylics in particular) if I do not de-tack it. FREE Shipping. Once you have finished, lift away the excess – you now have a camo mask! When it comes to mixing paint for the airbrush, there are lots of methods out there. With some experience behind us on painting solid colors, the next step is getting more than one color on a model. In some instances, simply applying a piece of tape over the model’s curved areas, and following the same pattern as outlined above, works fine. Please let me know what your favorite masking methods are, either in the comments below, or on my Facebook page! In my case, I found that spraying at around 28psi gave me the best results for this painting scenario. $49.99 $ 49. Remember to de-tack! if your painting three color scheme start with brush painting your camo by wiping the excess paint of the brush and gently dabbing the color on slowly building it up until you get the desired effect your after, then mix a slightly lighter base color thin it slightly and paint the entire model again covering your camo. This will give us more practice with laying down good color coats and continue to increase the comfort level with using an airbrush. The move from single color schemes to multi-color schemes means that there needs to be some sort of planning involved, in order to get the best results. I think this imparts a much nicer scale effect. For painting a freehand camouflage, the airbrush needs to be able to hold a fine line. Make sure the brush is clean. First, you need a model that has the first color of a camo scheme already applied. I would use heavy paper, such as construction paper, cut out the pattern, and get it as close to the surface as you can when painting. (Note- you can use masking fluid here, but in a few cases where I’ve done this, the masking fluid imparted a bit of color shift, which did not look nice. I find it helps to focus on very small sections at a time, using one hand to apply the tape, and the other to hold the tape down. So it’s a perfect way to illustrate the use of “curve” tape. At first, I don’t push it down, but leave it a bit loose for fine adjustment. You can use the instructions on the model for the camo pattern. Over the years, I’ve tried various methods, including the use of “Silly Putty”/Blue Tac, paper masks, pre-cut vinyl masks, and even trying to solely use liquid masks. And while it did allow for a very precise pattern, quite often the various curves and 3D shapes could not be properly accounted for by simply scaling up a 2D drawing. 99. One challenge is getting around the tight corners between the nose and engine nacelles. Free UK Delivery by Amazon. Carefully remove your mask section from the cutting surface, and then apply it to the model, using the small marks as alignment guides. 1-16 of over 1,000 results for "model aircraft paint" Skip to main search results Eligible for free delivery. (The undersides have already been painted and masked off. Paper masks worked OK too, but often suffered from the same “underspray” issue as putty. I don’t lift straight up, but rather try to keep the pulling motion parallel to the masked surface. While the initial thought is to use masking tape for everything, it is often wise to think outside the box and contemplate other options to achieve the same result. For this aircraft, we're going to move to a paint that needs to be thinned, and one which has a different drying method. The painting of a glossy finish such as used on automotive models follows a quite different path. Paint Masks for Scale Models: Aircraft, Armor and Helicopters. Then, using either tweezers or my fingers, I apply the tape, shaping it as I go. I am not a builder.